Drilling with a magnetic drill is done with the help of magnetic bases. This model drills up to a diameter of 120 mm in one step. Drilling is done very quickly and easily. The magnetic base of the drill sticks to the metal plate and makes holes in thick metals very easily and quickly without any movement with the highest security. Magnetic drills are used at heights and places where you cannot work with normal drills. In the following, the things that you should pay attention to while drilling with a magnet drill will be taught. Stay with us until the end.
Getting to know and training drilling with a magnet drill
Getting to know and training drilling with a magnet drill
At first, when you have just turned on the magnet drill, you should not use the high speed of the drill for the first 8 hours. After 8 hours, you can safely use the highest capacity of the device. When you want to turn on the device, you must turn on the magnet feature on the work surface you want. By turning on the magnet property, the device sticks firmly on the surface and the possibility of falling from a height or falling is eliminated.
Whenever you are done with the drill, turn off the magnetic property as it will stress the device and cause it to fail. During drilling, so that the drill does not overheat, be sure to use the tank for cooling on the machine. This makes the drills last longer.
If you work with HSS drills, you should not apply pressure to them because they are more fragile than other drills.
One of the important things that you should pay attention to while working is to take the drill properly. A loose rail causes the drill to break and the possibility of injury to the operator increases.
Click to know the difference between HSS and TCT drill.
How to take the slack of the drill for drilling with a magnet drill?
Turn on the drill. Set the engine speed to the lowest setting. You need to prepare two types of allen wrenches and hand wrenches and adjust the tightness of the slacker as follows.
With the help of an allen wrench, open the drill nuts a little to loosen them.
Tighten the specified screws with the wrench provided with the drill. Tighten the screws enough that the drill is firmly in place and requires little force to wiggle it.
Re-tighten the nuts that you have loosened to tighten the bolts and prevent them from loosening.
Never forget the grace. Lubricate the clutch at regular intervals to prevent corrosion. If the slack arrester is corroded during drilling, the drill bit may break. If you hold it correctly and loosely, the drills will break less and with this the life span of the drill will increase.
Click here to learn more about the safety tips for using a drill magnet.
In what industries is drilling with a magnetic drill used?
In what industries is drilling with a magnetic drill used?
Magnet drill is used for drilling on many metals and metal structures. In some types of magnet drills, you can also do hoarding and nailing while drilling. Each drill is designed for a job. So, so that the life of the drill does not decrease, use any drill for the same job. It is not recommended to use the magnet drill for other drilling purposes.
Magnetic drill is used in various industries. Industries such as:
Rail industries
Large manufacturing industries
Shed industries
Mobile repair shops
Oil, gas and petrochemical industry
Automotive industry and vehicles
Shipbuilding industries
Construction of steel structures
building industry
bridge industry
Production workshops
Metal welding workshops
The method of placing the drill on the magnet drill
Read this article to learn about the use of drill magnets in the industry and its components.
To place the drill, you should pay attention that first the pinrail, then the pin hole, then the drill bit and its groove, which is the place where the coolant passes, are in the same line. To make sure that the drill stays cool, it is better to clean the inner wall and the trail of the drill in advance.
First, insert the pin into the end hole of the drill. Insert the drill into the magnet drill spindle. The drill should be placed in the drill in such a way that the flat surface of the drill is facing the spindle screws. Then tighten them with an allen wrench.
Click to know the types of drill and its use.
Safety items when working with a drill
Safety items that should be taken into account when working with a drill
Drilling with a magnetic drill must be done on clean surfaces. If you want to drill on vertical or inclined surfaces, you must chain the drill. You must do this before turning on the device and during shutdown.
If you notice abnormal signs while working with the magnet drill, turn off the device first. Then look for the problem and fix it.
If you don’t need the magnet property and want to turn it off, it is better to turn off the device’s engine first and then disable the magnet property.
To protect your eyes, hands and ears when drilling with a magnet drill, be sure to bring gloves, earplugs and glasses.
Wear work clothes. Avoid wearing loose clothes and wearing decorative accessories such as separate bracelets and necklaces.
It is better to use the best drill magnet brands. In addition to long life, these drills have more security during use. You can buy from AF Powertools, Einstock, Jepson, BDS, Promotek brands.
Cool the drill with oil or spray before drilling. Cooling is better done both inside and outside the drill. This will increase the life of the drill and easy drilling of metals.
If you want
Replace the tip. You must turn off the machine and replace the drill in safety.
After the work with the drill is finished, the drill should be cleaned and dried so that it is ready for the next use.
Before turning on the device, make sure the tightness and looseness of the damper. If necessary, tighten the screws properly. Also, connect the drill to the correct voltage.
Do not use drill magnet if you are in dangerous environments where there are many flammable materials and gases. Because sparks are generated during the drill, which increases the possibility of fire.
Do not use drill magnet in wet environments. There is a possibility of electrocution for the operator.
Make sure that the base and the structure on which drilling is going to be done are strong.
Use AC power to turn on the device. DC power is not suitable for magnet drill.
Click to learn about the types of drill bits.
Basic characteristics of magnets
Magnetic drill consists of 3 main parts: magnetic base, drill base and motor. The magnet base plays an important role when drilling with a drill. In the following, we will get to know more about its efficiency.
Magnet base
The bases that are 12 mm are better and more quality than other bases in terms of quality. The strength of the magnet is determined by the coils of the drill magnet. This strength depends on the thickness of the sheet, the color and the surface on which the device is supposed to be placed. Make sure the drill is connected and the magnet button is on, then turn it on.
If your drill bit has two coils when drilling, make sure both are attached to the work surface.
Drilling method with magnetic drill
Drilling method with magnetic drill
If you follow the steps below when drilling with a magnet drill, the result will be better.
Use the tip of the pin to precisely mark the center where you intend to drill.
After determining the location of the hole, first make sure that the drill is sticking to the work surface, then turn on the machine.
Before you start drilling with a magnetic drill, open the coolant valve so that the drill does not get hot during operation.
Do not fasten the drill to the surface after turning it on. Wait a few moments for the engine to reach its maximum power. After that, do the drilling.
No need to apply too much pressure. Apply controlled pressure and be sure to keep the drill cool while working. Adjust the coolant valve on the drilling site to keep the drill bit cool. Be patient for drilling, do not rush.
Every time the drill reaches that side of the piece, reduce the pressure and complete the drilling with patience.
To turn it off, first pull the engine up by its handles. Then turn off the engine. Clean the shavings and flakes completely from the drill.
Read the article on the size and weight of the drill magnet for a complete understanding of this product.
How to maintain a magnet drill?
In order for the drill to have a longer life and work properly, you must clean it after each use. All shavings, cooling oil and dirt must be removed from the machine.
Always check the engine carbon and replace it if it is corroded. If you notice a part failure on the device, repair it as soon as possible so as not to damage other parts.
In addition to checking the grease of the rails, the gearbox should also be checked so that if the grease of the gearbox is low, you can increase it.
The thing that you should be very careful about is the lagging every time you use the device.
Conclusion
In this article, we examined drilling with a magnetic drill. By reading the necessary instructions, you can use the magnet drill confidently. If you intend to buy a drill magnet, you can call the numbers on the site. Our professional consultants guide you for free to buy the best brand and the highest quality drill. You can buy all household and industrial tools, such as magnetic drills, chamfers, and rotary drills, from Radiran’s specialized tools site. We are waiting for you in Radiraan.
