Magnet drill is used as a professional tool in workshops and construction projects. This drill is also known as magnetic drill and magnetic drill in the market. In fact, the use of drill magnets in the industry is very high. Working with a magnetic drill is for drilling metal and steel. When using the magnet drill, you no longer need to move the desired surfaces. Magnetic drill is light and portable. In this article from the Radiraan website, we will get to know the magnet drill and its work.

Tips for using a drill magnet

Getting to know the magnet drill
Magnetic drill or magnet drill is an electric device for cutting and drilling metal. This device consists of three main parts: magnetic base, drill base and motor.

The importance of knowing the safety tips of the magnet drill
Working with a magnet drill is very easy. You just have to follow the things that are said so that the life of the device is long.

Safety tips for using a magnet drill, if followed, you can easily use this device in places that are difficult to access. The most important point in the safety of the device is to make sure that its magnetism is working properly. With the help of this drill and its magnetic base, it can be easily fixed on different surfaces. In places such as truck boards, large and fixed metal parts such as the skeleton of a building where it is not possible to move anywhere, the best way is to use a magnet drill. This cannot be done with ordinary drills. In the following, we will state the points that you must follow for loosening and also for using the magnet drill.

Click to view and buy the rotary drill.

Safety tips for using a magnet drill
Place the magnet or magnetic drill on a flat and clean surface. If you want to use the drill horizontally, be sure to close the drill chain. The drill must be turned off when closing the chain.
If a problem occurs during drilling, turn off the machine first. After that, go to troubleshooting.
Before turning off the magnet button, turn off the engine key.
Before starting work, be sure to prepare gloves, glasses and earplugs.
Do not wear bracelets or jewelry while working with a magnet drill. Wear appropriate work clothes to maintain your safety.
In order for the drill to work better, it must be lubricated inside and out before starting to work.
The drill in the magnetic drill produces high heat. For this reason, you must use coolers. For this purpose, a soapy water tank is provided on the device. Before starting work, you should install it on the drill and fasten the hose of the soapy water tank to the device with the help of the nut on it.
After fixing the drill on the work surface, open the tap of the soapy water tank to prevent the drill from getting hot during drilling. Now safely turn on the device by pressing the key and work with it. Don’t worry about the longevity of the drill. With this, you can use the drill for a long time.
If you want to change the drill, unplug the machine first so that you can change the drill safely.
When finished, clean and dry the drill.
Before starting work, make sure that the screws and nuts of the device are tight.
Do not use the drill magnet if you are in a place where there are gases and condensate. It causes explosions and fires due to the sparks produced during drilling.
It is not allowed to use drill magnet in wet environments. Because there is a possibility of electric shock.
First of all, make sure the device is firmly on the desired surface. Then turn on the magnet drill.
The drill must be powered by AC power. DC power is not suitable for working with a drill.
Use a direct power outlet so that the magnetic power of the device does not decrease during use.
Do not under any circumstances stand under the drill while working.
If you are going to use this drill on non-magnetic surfaces, be sure to use pipe clamps and a vacuum system.
The method of lagging while working with a magnet drill

How to catch the slack of the drill magnet?
There are rails in the magnet drill. Rails should never be loose. This looseness can cause the drill bit to break. So, when using a magnet drill, be sure to read the rail adjustment methods carefully. One of the most important safety tips for using a magnet drill is to catch the drill’s slack, which causes the drill to break during work. For this, you have to go through several steps to get rid of it. Next, we will review these steps together.

The method of lagging while working with a magnet drill
First, turn on the device.
Set the engine power to its lowest setting.
Start screwing with the allen wrench and the wrench that comes with the device.
Loosen the nuts a little with an Allen wrench.
Tighten the screws with the wrench provided.
Tighten the screws enough to hold the motor in place. There is no need to use a lot of force when using the magnet drill.
Tighten the screws as desired so that they do not loosen during use.
It is better to grease the clutch at regular intervals. By doing this, the slipper will not get corroded. Keep in mind that loose rails are one of the most common causes of drill bits breaking during drilling. If you do these things correctly, the drill will stay healthy.
Magnet base safety tips
The use of a drill base has made this piece one of the most important components in a magnet drill. It is better to make the base from 12 mm sheet or higher. The magnetic ability produced in the magnet drill depends on the thickness, color and desired surface. For this reason, before starting work, make sure the level of adhesion of the device to the surface. Egg

Your device has two coils, make sure both are attached to the surface.

In what cases is working with a magnet drill a priority?
It is often used for drilling on metals in bridge building, shipbuilding, welding workshops, railways, facilities, oil and gas lines, and in building construction.

In addition to drilling holes, the magnet drill is also used for vaulting and nailing. We recommend that you use the magnetic drill only in the cases for which the magnetic drill is made. You can do other things with other drills.

Safety tips for using a magnet drill

Maintenance before and after work with drill magnet
Always keep the drill clean to extend its life. Keep the drill clean of shavings, dirt and oil.
After using the magnet drill a few times, it is better to check the motor’s coals. If the coals are corroded and misplaced, it is better to change them.
Lubricate the rails with grease, this will increase the life of the drill.
During work, if a part is damaged, you must first unplug the device. Then repair that part so that other parts are not damaged.
Every time you use the drill, be sure to check it.
Conclusion
The use of magnet drill in construction, road construction, shipbuilding and other industries is inevitable. In this article, we got acquainted with the magnetic drill and checked its usage and maintenance methods together. If you intend to buy a magnet drill or other industrial and household tools, you can visit Radiran’s website and make the best purchase. Also, our professional consultants can guide you in choosing high-quality equipment suitable for your work. We are waiting for you in Radiraan.